跳转至内容

Wi-Fi HaLow™

23 主题 75 帖子

子版块


  • 21 72
    21 主题
    72 帖子
    T
    ============================================================ Morse Micro <-> TaiXin IP Allocation Issue Summary [ Current Situation ] AP : Morse Micro MM8108-EKH05 STA : TaiXin AH Module Symptom: Unable to obtain IP address (DHCP failure) Cause : "Invalid group cipher (0)" -> Connection fails at WPA authentication stage [ Problem Flow ] TaiXin STA -> Scans for Morse Micro AP (SSID found) | v Attempts WPA Authentication | v Invalid group cipher (0) <-- Security spec mismatch | v Association Timeout | v Disconnect -> Retry Loop | v Result: No IP address assigned (fails before DHCP stage) [ Root Causes ] TaiXin module is running in proprietary protocol mode (wnbsta) Morse Micro AP supports only standard WPA2-PSK Not compatible with TaiXin's proprietary PAIR mode Failure to parse security specifications TaiXin cannot parse the WPA2 security header from the Morse Micro AP Result: group cipher = 0 (unrecognized) Consequently, failure occurs at the Association stage IP allocation (DHCP) happens only after successful Association Therefore, this is NOT an IP issue, but a connection-stage issue log data "-------------------<CR><LF> [1051276]LMAC STATUS:<CR><LF> local: ce:4f:26:8f:aa:88 AID= 0 mode= 0(0/1:STA;2:AP)<CR><LF> freq= 916.0 bw=1 bgr=-106 dc=0:0(5:44) <CR><LF> chn: 908.0 916.0 924.0 <CR><LF> bgr: -60 -60 -60 <CR><LF> buf: free=65 tq=0 sq=0 <CR><LF> irq: ac=42 bkn=0 bo(rts:frm)=0:0:0:0:42 to(rts:frm)=0:0 rx=52<CR><LF> tx : cnt=42 dly=0:0ms est_rate=900kbps txp=0 fail=0 drop=0 <CR><LF> rx : cnt=52 bus=0ms<CR><LF> cca: st12= 0:0 mid1224= 0:0:0:0<CR><LF> chip-temperature:36, vcc:3.37, vdd13b:1.35, vdd13c:1.34<CR><LF> sta_list: no sta<CR><LF> <CR><LF> <ESC>[1051550]ieee80211_sta_select_bss:24::by SSID find hgic_ah_test [50:2e:91:d2:c4:c9] at channel 2<CR><LF> <ESC>[1051559]vif1 state WPA_SCANNING -> WPA_AUTHENTICATING<CR><LF> [1051569]Invalid group cipher (0).<CR><LF> [1051570]vif1 state WPA_AUTHENTICATING -> WPA_ASSOCIATING<CR><LF> <ESC>[1052476]ieee80211_sta_assoc_timeout:53::connect to ap 50:2e:91:d2:c4:c9 timeout, disable it!<CR><LF> <ESC>[1052484]ieee80211_sta_disconnect LR= 0x20048df4. 50:2e:91:d2:c4:c9<CR><LF> [1052490]lmac set GTK: cmd=1 addr=50:2e:91:d2:c4:c9 cipher= 0x0 flags= 0x0 keyidx= 0 keylen= 0<CR><LF> [1052498]del_STA: addr=50:2e:91:d2:c4:c9<CR><LF> [1052502]stamap=0x0<CR><LF> [1052503]sleepmap=0x0<CR><LF> [1052505]vif1 state WPA_ASSOCIATING -> WPA_DISCONNECTED<CR><LF> [1052511]vif1 state WPA_DISCONNECTED -> WPA_AUTHENTICATING<CR><LF> [1052516]vif1 state WPA_AUTHENTICATING -> WPA_SCANNING<CR><LF> <CR><LF> "
  • 需要一个txw8301的flash的烧录固件

    1
    0 赞同
    1 帖子
    37 浏览
    T
    能否发一份新版固件用于烧录,我将txw8301_v2.4.1.3-43933_2026.7.24_TAIXIN_WNB.bin烧录到flash,串口提示错误,可以的话请发邮箱2929475544@qq.com
  • 关于txw8301流控的问题 模组频繁出现pending

    2
    0 赞同
    2 帖子
    122 浏览
    T
    已确认,使用的版本是hgSDK-v2.4.1.5-38247,在最新的版本hgSDK-v2.4.1.5-43379上已将该问题解决。